Why is my spa overheating?

If the spa is located in an area that is experiencing hot weather, it is normal to have the spa water temperature rise. To help keep your spa cooler, adjust the spa’s filtration cycles to no more than three hours per day, and only one hour per day during the warmer summer months. Set the cycles to run during later evening or early morning hours when the outside air temperature is cooler. During the summer, set only one filter cycle per day. Open the cover for several minutes, long enough to allow the water to cool down. Repeat a couple times weekly as necessary. For safety reasons, never leave your spa unattended with the cover open. If OHH is displayed on the control panel, this means that the thermometer has detected spa water temperature above 110 degrees F. Do not use the spa at this temperature. Take the advised steps above to cool your spa water to below 106 degrees F before use.

Why won't my spa heat?

If your spa temperature is low, first check the thermostat to see if it has been turned down or set to low heat range. Adjust the thermostat to desired temperature or set to high heat range. Another common reason for your spa temperature to be low is because the high limit sensor has tripped. Press any button on your control panel to reset the system. If neither of the above steps works, your heating system may be defective. Contact your authorized Bullfrog Spas Dealer for further diagnosis.

Why is my GFCI breaker tripping?

Warning: You must be a qualitied electrician and or service technician to perform diagnosing or serial injury or death can result: High voltage components are in use. If the spa was recently installed, the most common reason the GFCI would trip is the Load Neutral (white wire) between the spa and GFCI which must be connected to the Load Neutral port in the GFCI breaker. If the neutral wire is connected to the neutral busbar, the breaker will trip during startup. The neutral connection must not have contact to the ground on the load side of the breaker or it will trip. If the spa is not tripping immediately upon startup, a process of elimination should be used to identify the problem. Disconnect one component at a time from the control board and try restarting the spa. If the breaker trips, reconnect the component then try again by disconnecting a different component. Continue repeating this process until the breaker does not trip. Components include pumps, heaters, lights, stereos, ozone, etc. If the breaker does not trip after disconnecting the component, then the disconnected component is the source of the problem. Once you have determined which component is at fault, replace the component. If you have not found the source of the problem after disconnecting each spa component individually, disconnect all components from the control board and try starting the spa. If the breaker still trips, a certified electrician will need to inspect the breaker and wiring.

Why is my spa making a vibration noise?

A light vibration noise is normal while the spa pumps and motors are running. If your spa’s vibration noise level seems excessive, the first thing to check for is the spa motor’s shipping bolts. Each spa motor has a shipping bolt that can contribute to the vibrating noise and can be removed once your spa is delivered and installed. The bolts have tags with red lettering for easy identification. If the bolts have been removed and your spa still makes an excessive vibration noise, contact your spa dealer for further assistance.

Why is my spa pump creating a burning smell or making excessive noise?

If your spa pump is creating a burning smell or making excessive noise, the pump motor is defective. This can happen when running the pump during high ambient outside temperatures or due to excessive run times. Please contact your authorized Bullfrog Spas dealer for replacing the pump.

Why are my control pad and spa equipment not operating?

If your hot tub control pad and spa equipment are not operating, that means you have no electrical power to the spa. Turn on or reset the GFCI circuit breaker to supply the spa with power again. If this does not solve the problem, have a qualified Electrician check the electrical service for issues. Another reason your control pad and equipment won’t work is if the fuse (20 or 30A depending on the system) has blown. Contact your authorized Bullfrog Spas Dealer for repair/replacement.

Why are my hot tub jets not working?

If your hot tub jets are surging on and off, the first thing to check is your water level as it might be too low. Adjust water to the water level indication mark on the faceplate of the filter assembly. Next, check your filters as they may be dirty. If so, clean or replace them. If your spa’s jets seem weak or are not working, first double-check to make sure that the valves are open. JetPaks have valves at the bottom that open and close by turning the valve. Adjustable jets on M Series, A Series, R Series, and STIL spas open and close by turning the jet face. Adjustable jets on X Series spas open and close by turning the outer ring. The next thing to check is the suction fitting(s) normally located at the bottom of your spa shell to see if they are blocked. Remove any debris you find by hand or with a spa vacuum. If your jets are not working after filling your spa, you most likely have an airlock in the pump. Follow the directions in the “how do I fix an airlock in the pump” section below.

Why won’t my spa won't work after draining and refilling it?

If your spa pumps/jets are not working after filling your spa, you most likely have an airlock in the pumps. Follow the directions in the “how do I fix an airlock in the pump” section below.

How do I fix an airlock in the pump?

To prevent airlocks when filling your spa, be sure to open all valves in the JetPaks and all other jets in the spa before filling to allow as much air as possible to escape from the system during the filling process. Fill your spa through the filter by taking the filter cap off and put the hose directly in the filter. Detailed instructions for filling each spa series are found in your owner’s manual. Your hot tub’s pumps must be primed directly after filling to ensure correct operation of your spa and get rid of any airlocks. After initial startup, verify that the home status screen appears on the panel. Depending on your spa model, your spa has either 1,2, or 3 pumps. To prime the pumps, press the “Jets 1” button once to prime in low-speed. After the pump turns on and water is visibly flowing from the jets wait a few seconds and then press “Jets 1” again to initiate highspeed operation of Pump 1. The pump has primed when water is flowing from the jets. If your spa is equipped with a second jet pump, repeat the priming process for Pump 2 by pressing the “Jets 2” button once to turn on low speed and then a second time to turn Pump 2 on high. If your spa has a 3rd pump, press the “Jets 3” button to prime the third jet pump. All pumps will have primed when water is observed flowing from the jets associated with each pump. On rare occasions, priming the pumps will not get rid of an airlock. The next step is to remove the front panel and locate the pump with an airlock. The wet-end of the pump has a bleed valve—loosen this until all the air escapes and water starts to drip out, or loosen the union on the pump to let the air out until you see water. Do not attempt this while the spa pump is running. If you need help doing this or this does not resolve the problem, please contact your authorized Bullfrog Spa Dealer.

Why do my spa jets turn off during operation?

If your jets turn off automatically after either 30 or 60 minutes, this is completely normal. The automatic timer has completed its cycle. Simply turn the pump back on to start a new cycle. Another reason your jets can turn off unexpectedly is if the pump has overheated due to the vents on the equipment door being blocked. Clear away any items from the vents and wait a while to see if your jets work again. The last reason your spa jets can turn off is if the pump motor is defective. In this case, contact your authorized Bullfrog Spas dealer for service.

Why are my hot tub jets/pump not turning off?

If you are trying to turn off the pump for jets 1 on your spa and it appears that they are not turning off, your spa is in the middle of a filtration cycle. Spas not equipped with a dedicated filtration pump will turn on automatically, using jet pump 1 on low speed, to filter and/or heat. This is normal spa operation.

What do I do if my spa is leaking?

If you notice your spa is losing water, check all fittings and equipment in the equipment compartment for the source of leakage. If a leak is detected, tighten the fitting by hand. If the leak persists, you cannot find the source of the leak, or the leak is coming from the shell, contact your authorized Bullfrog Spas Dealer.

Creating Healthy Routine Around Your Bullfrog Spa

29 June

Share on
Share
Tweet
Share

Couple relaxing peacefully in a bullfrog spa

Creating a Healthy Routine and Good Habits Around Your Hot Tub

Bullfrog Spas | Ownership, Benefits & Features | No comment

Bullfrog Spas, and hot tubs in general, don’t just improve the aesthetic of your backyard but also can be utilized as a tool to enhance relaxation and improved well-being. To make the most of your spa experience, it’s essential to establish a routine and develop healthy habits that maximize its benefits. We will guide you on how to create a routine and incorporate good habits around your hot tub, while also highlighting the numerous health benefits it offers.

Set a Regular Schedule

Establishing a consistent schedule for spa sessions will help reap the long-term health benefits. Determine a time that suits you best, whether it’s in the morning, after work, after or before a workout, or before bedtime. Making it a habit will make it easier to prioritize your health and relaxation, even on a busy day or week. Depending on what muscle you’d like you target, pick a JetPak or seat that is suited for those needs. Aim for 20-30 minutes per session. This will ensure you have enough time to unwind, relax, and enjoy the benefits of hydrotherapy.

Make it Fun

To make your hot tub experience fun, invite friends or loved ones to join you! Consider having entertainment options like waterproof speakers or games. Bullfrog Spas offer an optional audio system hidden within the spa shell that allows you to enjoy your favorite tunes! You can also provide drinks and snack to create the ultimate get-together. These small details can transform your backyard into the go to family and friend hang out spot.

Improve Relaxation

Consider adding soft lighting, soothing music, or aromatherapy to enhance your Bullfrog Spas experience. By setting the right atmosphere, you can help your mind and body unwind and release stress.

Practice Hydration

Staying hydrated is essential while using your Bullfrog Spa or hot tub. Drink a glass of water before and after each hot tub session to help replenish lost fluids and to maintain optimal hydration levels. Proper hydration supports circulation, aids in detoxification, and promotes overall well-being.

Warm-Up and Stretch

Warming-up and stretching isn’t just for working out. It can also help increase blood flow, loosens muscles, and prepares your body for hydrotherapy. Before using your spa, spend a few minutes warming up your body and performing light stretches.

Utilize Jet Therapy

Most Bullfrog Spas offer a JetPak Therapy System that gives you the ability to customize your spa experience. With this feature, you are able to switch out your JetPaks and find the right JetPak that targets specific areas of your body.

With your spa, experiment with different JetPaks or jet seats to find what works best for you. Focus on areas that need relief, such as sore muscles or tension points. Jet therapy can help alleviate muscle pain, improve circulation, and reduce stress.

Incorporate Mindfulness and Meditation

Your spa time can also be an opportunity for mindfulness and meditation. Practice deep breathing techniques, visualize serene scenes, or listen to guided meditations. This combination of hydrotherapy and mental relaxation can decrease stress and promote a sense of well-being.

When utilized correctly, spas and hot tubs yield many health benefits. Spas can help with stress relief and enhance well-being. Regular use of a spa can reduce stress levels, promote relaxation, and alleviate anxiety. Relaxation has been known to lead to better sleep quality and duration. Hot tubs also stimulate the release of endorphins, promoting a positive mood, and reducing depression symptoms. Another benefit is muscle recovery and pain relief. Hydrotherapy can aid in muscle recovery after exercise or physical exertion by promoting blood circulation and reducing inflammation. The combination of warm water and jets can help relieve joint pain, muscle tension, and chronic conditions, such as arthritis.

A hot tub is not just a luxury but a tool for self-care and achieving a healthier lifestyle. By creating a routine and healthy habits around your hot tub, you can maximize your overall experience of your Bullfrog Spa and hydrotherapy.

Become a Bullfrog Spas Brand Ambassador

Do you love your Bullfrog Spa? If so, we want you to become a brand ambassador. Get rewarded for sharing about your Bullfrog Spas experience with your family and friends. Apply today!

AUTHOR - Bullfrog Spas

Bullfrog Spas is a premier brand of personalized premium hot tubs. With proprietary hydromassage technology and an eye for contemporary design, Bullfrog Spas is revolutionizing the concept of the portable hot tub and providing a relaxation experience unlike any other. Discover the award winning spa of the future today.

Blog